Who its for: licensed fridgies, service techs and apprentices who need a reliable 30-amp interposing relay to let Dixell XR-series controllers switch higher loads safely. Its a simple add-on that keeps jobs tidy and compliant, no worries.
Key Features & Trade Benefits
- 30A contact ratinggives your controller the grunt to switch compressor, fan, or defrost loads via an external relay (less stress on controller outputs, fewer call-backs).
- Interposing relay for XR-seriesideal when the controllers onboard relay isnt sized for the load; wire through RELAY30 for safe, stable operation.
- Simple two-stage controlcontroller drives RELAY30; RELAY30 switches the actual loadbloody good for neat panel layouts.
- Field-serviceable formatstraightforward terminals and clear markings make swaps quick when youre against the clock.
- Broad applicationcoolrooms, freezers, merchandisers, and HVAC plant where external load switching is required.
Why This Product Matters
Controller relays arent always built to handle compressor inrush or defrost heater currents. The RELAY30 acts as your workhorse between the controller and the load, protecting the brains while the muscle does the heavy lifting. Quick anecdote: tech on a steamy Sydney arvo had a cabinet compressor chattering on start. Dropped in an external 30A relay, tidied the wiring, and fair dinkumsystem pulled down clean with no more nuisance trips.
Comparing controllers or adding spares? Browse the Dixell range here:Dixell brand collection .
Pro Tip
- Match coil/control voltage: wire the relay coil to suit your panel supply or the controllers output specs. If unsure, check the controller manual and panel drawings.
- Cable management: route away from heater runs and sharp edges; label both the coil feed and switched load so the next tech can fly through service.
- Safety first: isolate and test before you touchlockout/tagout and follow site procedures.
Compatibility & System Info
Designed as an external 30A interposing relay for Dixell XR-series controllers (e.g., XR20CX/XR60CX) when higher load currents demand an additional switching device. Always confirm load current, inrush, and wiring method in your controller documentation.
Typical Aussie jobsites: hot rooftops in Brisbane or salty coastal air in Sydney. Keep terminations tight, use correct ferrules, and enclose against moisture where neededshell be right.
Pair with a controller like theDixell XR20CX-B Medium Temp Controller .
Whats Included
- 1Dixell Relay 30AMP (Model: RELAY30)
Specifications
| Attribute | Details |
|---|---|
| Model | RELAY30 |
| Contact rating | Up to 30 A (use appropriate protection and wiring method) |
| Use case | Interposing relay for controller outputs (compressor / fan / defrost) |
| Controller family | Dixell XR-series (verify controller output specs) |
| Mounting | Panel/enclosure (installer to select suitable base/fixings) |
| Compliance | Install per site electrical rules and WHS procedures |
Warranty & Returns
Covered by the manufacturers warranty. See ourShipping & Returnsfor details on returns and exchanges.
FAQs
Will RELAY30 work with my XR20CX?Yesuse it as an external interposing relay when the controlled load exceeds the controllers onboard relay rating. Always check the XR manual.
What loads can I switch?Commonly used for compressors, condenser/evaporator fans, or defrost circuits. Confirm actual current (including inrush) and protect the circuit appropriately.
Do I need a potential relay as well?Different role. A potential relay is for motor starting; RELAY30 is for load switching.
Any safety guidance?Yesfollow WHS electrical safety practices and isolate before work. See Safe Work Australia guidance below.
Related Products
- Dixell XR20CX-B Digital Controllerideal controller pairing when youre rebuilding a medium-temp cabinet.
- Universal Potential Relayfor compressor starting duties (different to load switching, but often installed together).
- ICG220 Solid State Relay (220V)an option where solid-state switching is preferred.
Compliance & Good Practice (Authoritative)
For electrical safety guidance (isolation, testing, and managing electrical risks), refer toSafe Work Australia .









